X144 LED Door Indicator Light System with MGM Panel

Each LED Strip Assembly comes with pre-installed Pressure Sensitive Hook and Loop Velcro Strips.

Peel the Clear Backing off each Velcro Strip (6 Total) and stick the LED Strips onto the Vertical Tracks.

The LED Strip with the longer cable (25ft) is mounted on the non-drive side of the opening.

Ensure the LED Strip is oriented such that the shortest possible length of Cable is needed to reach the Control Panel.

The LED Strip with the shorter cable (10ft) is mounted on the drive side of the opening.

Ensure the LED Strip is oriented such that the shortest possible length of Cable is needed to reach the Control Panel.

DO NOT LENGTHEN EITHER OF THE LED STRIP CABLES AS THIS MAY CAUSE INCONSISTENT PERFORMANCE. THE PROVIDED CABLE LENGTHS ARE IN THEIR 'WORST-CASE' CONFIGURATION.

If the provided Cables do not reach the Control Panel, you will need to re-route them, or add a Junction Box to house the Microcontroller (see next step) in a location where both Cables can reach it.

In your Kit, you will also find the following:

One Microcontroller.

One Power Supply.

5-Condcutor Cable to make the necessary Electrical Connections inside the Control Panel.

Once you have routed the Wires from the LED Strips into the Control Panel, you will have to make a series of Electrical Connections.

Find the 5-Conductor Cable provided with the LED Light System.

Colors: Green, Blue, Red, Yellow, White

Located the J3 Terminal Block

Note the Orientation of the Microcontroller in the Diagram.

Make the following Connections on the Microcontroller (from Top to Bottom) using the 5-Conductor Cable:

White, Yellow, Red, Blue, Green

On the other end of the 5-Conductor Cable, the wires Terminate in the Control Panel as seen in Images 2.

WHITE WIRE SHOWN AS BLACK ARROW IN IMAGE 2.

Multiple Wires can be placed in the same Terminal.

(2) Jumper Wires will need to be added in the Control Panel between 24VDC to Opn-Lim, and between 24VDC to Clo-Lim.

Bring the (2) 3-Conductor Cables from the LED Strips into the Control Panel.

Locate the J6 and J7 Terminal Blocks

Note the Orientation of the Microcontroller in the Diagram.

Each Terminal Block receives Wires from One of the LED Strips.

Make the following Connections (from Top to Bottom) on each Terminal Block:

Red, White, Empty, Empty, Empty, Black

Locate the Provided Power Supply.

Bring Power (Single-Phase 120 to 240VAC) to the Power Supply via the Plug or by Hardwiring.

Power needs to come from an Outside Source, and should NOT be pulled from the Supply that is feeding your Control Panel.

Make sure Electrical Requirements can be fulfilled without straining the System.

Cut the Barrel Connector off of the Output Side of the Power Supply.

Bring the Power Supply Output into the Control Panel.

Locate the J9 Terminal Block

Note the Orientation of the Microcontroller in the Diagram.

Make the following Connections (from Top to Bottom):

Red, Black

Before we can Program our LED Door Indicator Light System, we must set up the Time-to-Close (TTC) Feature on our Control Panel.

From the Home Screen Press the "SETUP AND DIAGNOSTICS" Button.

On the Next Screen, Press the "SETUP" Button.

Tap and Enter your Password.

Default Password is 123.

Tap the "SETTINGS" Button.

On the Next Screen, Press the "AUTO CLOSE TIMER" Button.

To Enable the Auto Close Timer Program, Tap in the Program box, and Type "1" in the on-screen Keypad. Hit Enter.

Tap the "NEXT SCREEN" Button.

To Set the Auto Close Timer value, Tap in the Set Point box, and in the on-screen Keypad, Type the desired Time (in seconds) before you want the Door to Automatically Close. Hit Enter.

Tap the "MAIN SCREEN" Button.

Then Tap the "OPERATOR SCREEN" Button.

Your Auto Close Timer is Setup!

When first Powered On, the LED Strips will Flash Green for One Second. At this Point, Proceed to the

If at any point, you need to Restart the Programming Sequence, Press the 'RESET' Button.

When the 'RESET' Button is Pressed, the LEDs will Flash Green for One Second. When the Green turns Off, you are ready to Begin the Programming Process.

Locate the Blue Button Labeled SW1

Each Press of this Button adds One Second to the Timer associated with the LED Light System (10 Presses = 10 Seconds).

To Sync the LED Light System with your Control Panel, you must Press SW1 One time for every Second Programmed on your Control Panels' TTC Feature.

If your TTC is set for 10 Seconds, you must Press SW1 Ten times.

Locate the Blue Button Labeled SW2

Once you have Synced your LED Light System with your Control Panel by Pressing SW1, Press the SW2 Button One time.

This Locks in your Programming, and Initiates the Light System's Operation.