MGM Electric Motor + MGM Encoder Installation

Make Sure the Clamp Collar/Coupler is on the Bottom of the Encoder!

Note the Small Shaft Protruding from the top of the Motor.

Install the Encoder Unit into the Mount until it Falls/Locks into place and cannot Rotate within the Mount.

Install the Encoder and Mount Assembly onto the Motor Housing using the Provided Socket Cap Bolts, Lock Washers, and Hex Nuts.

Make sure the Coupler on the Bottom of the Encoder, Fits over the Shaft on the Top of the Motor.

Tighten The set Screw on the Clamp Collar/Coupler to Positively Secure the Encoder to the Shaft so that they rotate together.

(4) M6 x 10mm Socket Cap Screws

Requires 5mm (3/16in) Allen Wrench

(4) M6 Split-Lock Washers

(1) Motor Mount Anti-Torque Bracket

Note the Orientation of the Bracket in Relation to the Motor.

The Bracket has 2 Hole-Patterns Corresponding to G1 and G2 Doors. This ensures the proper Alignment when Installing the Motor Assembly onto a G1 or G2 Door.

For a G2 Door, Use the G2 Hole Pattern, and Vice Versa.

G1 Doors include Model 2000 and Clean Guard.

G2 Doors include Wash Guard, Harsh Guard and Machine Guard.

On a LH Drive, G2 Door, the Letters will Read Normally/Forward when the Bracket is Mounted onto the Motor.

Place the Bracket up on the Motor with the proper Hole Alignment.

Place the Lock Washer onto the Screw and Fasten the Bracket onto the Motor.

Note the Orientation of the Bracket in Relation to the Motor.

The Bracket has 2 Hole-Patterns Corresponding to G1 and G2 Doors. This ensures the proper Alignment when Installing the Motor Assembly onto a G1 or G2 Door.

For a G2 Door, Use the G2 Hole Pattern, and Vice Versa.

G1 Doors include Model 2000 and Clean Guard.

G2 Doors include Wash Guard, Harsh Guard and Machine Guard.

On a RH Drive, G2 Door, the Letters will Read Backwards when the Bracket is Mounted onto the Motor.

Place the Bracket up on the Motor with the proper Hole Alignment.

Place the Lock Washer onto the Screw and Fasten the Bracket onto the Motor.

Note the Orientation of the Bracket in Relation to the Motor.

The Bracket has 2 Hole-Patterns Corresponding the G1 and G2 Doors. This ensures the proper Alignment when Installing the Motor Assembly onto a G1 or G2 Door.

For a G1 Door, Use the G1 Hole Pattern, and Vice Versa.

G1 Doors include Model 2000 and Clean Guard.

G2 Doors include Wash Guard, Harsh Guard and Machine Guard.

On a LH Drive G1 Door, the Letters will Read Backwards when the Bracket is Mounted onto the Motor.

Place the Bracket up on the Motor with the proper Hole Alignment.

Place the Lock Washer onto the Screw and Fasten the Bracket onto the Motor.

Note the Orientation of the Bracket in Relation to the Motor.

The Bracket has 2 Hole-Patterns Corresponding the G1 and G2 Doors. This ensures the proper Alignment when Installing the Motor Assembly onto a G1 or G2 Door.

For a G1 Door, Use the G1 Hole Pattern, and Vice Versa.

G1 Doors include Model 2000 and Clean Guard.

G2 Doors include Wash Guard, Harsh Guard and Machine Guard.

On a RH Drive G1 Door, the Letters will Read Normally/Forward when the Bracket is Mounted onto the Motor.

Place the Bracket up on the Motor with the proper Hole Alignment.

Place the Lock Washer onto the Screw and Fasten the Bracket onto the Motor.

Install the Machine Key onto the Drive Shaft with the Set Screw Oriented Towards the Header (Between Motor and Door).

Slide the Motor onto the Shaft and Key.

Tilt the Motor to Align the Hole in the Motor Mount Bracket with the Hole on the end of the Upper, Front Rail.

This should result in the Motor being oriented Vertically and Plumb (See Image 2).

Place the 5/16 Flat Washer onto the 5/16-18 x 1/2in Hex Bolt and Fasten the Motor to the Door with a Ratchet or Impact Driver.