Integrated Weather Wall

Technical Support Contacts:

Phone: 262-746-3374

Email: techsupport@goffscw.com

Website: http://www.goffsenterprises.com

Measure Roof Frame width from outside edge to edge and take note.

Measure the door width and divide that number by 2 to determine the centerline of the door opening.

Take the Head Frame width from the previous step and divide that by 2 to determine the Side Pad offset from the door opening centerline.

Using the Side Pad offset dimension, mark lines from the centerline of the door opening to each side of the door opening.

Make a mark towards the top and bottom of each side of the door opening to help ensure the Side Pads are plumb.

These marks will be used in a later step to align the outside edges of the Side Pads.

Identify the Left and Right Side Pads

The front of the pad will have (2) strips of Velcro running up the length just on the inside of the left and right faces, and the Inside face will have (2) strips of Velcro to attach the Draft Pads towards the bottom of the Side Pad.

Once you have the Left and Right Pads identified, line them up so the outside faces are flush with the marks made on the wall in the previous step to make sure the whole Side Pad is plumb.

Measure the length of your Header Brackets and add 2" to that number to get your top Mounting Bracket dimension X.

Fasten the Side Pads to the wall using the Angle Brackets on the outside face by fastening (2) of the provided Hex Head Screws into the backer of the Side Pad and using an anchor to attach to the mounting surface. Fasten brackets X" from the top, 12" from the bottom, and one centered in the pad.

Fasten 3 more brackets on the inside face of the pad in the same locations as above. You will be provided either Angle, Offset, or Flat brackets for the inside face installation based on the Door Opening Width.

Attach the Left and Right Face Curtains by lining up the Velcro Strips towards the front of the Side Pad On the left and right faces with the Velcro Strips on the back of the Side Curtains.

Attach Draft Pads by lining up the Velcro on the back of the Draft Pad with the Velcro on the bottom of the Side Pad.

Secure the Draft Pad by fastening a provided Hex Head Bolt through the Grommet Tab of the Draft Pad into the Backer of the Side Pad.

Head Frame Cover is hidden to show detail.

Note that the 2x8 Board is the front of the unit, and the Header Brackets should be flush with the 2x4 Board on the back of the unit.

Orient Header Brackets onto the Head Frame as shown.

Fasten the Header Brackets to the Head Frame using the supplied Hex Head Screws.

Place the wiper pad on the face plate of the head frame. Center the Pad on the Front 2x8 Board with the top corners of wiper pad flush with top of the Head Frame.

Lay attachment flap down & fasten in place with (3) flat head roofing nails to temporarily secure Wiper Pad.

Place Aluminum Angle Trim over Attachment Flap and fasten with provided Hex Head Screws fastening every 11"-12".

Wiper Pad and Head Frame Cover hidden to show detail.

Align the Head Frame Assembly so that The Header Brackets are on the outside of the Side Pads, and Flush against the mounting surface.

Anchor Head Frame Supports to the mounting surface using concrete anchors or by using other best practices using the (3) pilot holes in the Bracket.

Secure Head Frame to the mounting surface by drilling through the back 2x4 using at least (3) concrete anchors, or by using other best mounting practices.

Wiper Pad and Head Frame Cover hidden to show detail.

Center The Top Face Curtain and fasten it to the Center Horizontal Beam on The Head Frame all the way butted up to the top of the Cross Beams on The Head Frame using the provided Hex Head Screws.

Use a fastener through the top of each Stiffener in the Top Face Curtain and one on each end as shown.

Install two Eye Screws with the Aircraft Cable through the Angle Trim and into the Head Frame 12" off center.

Secure the other side of the aircraft cable using best practices for your surface material to anchor the cable to the mounting surface.

Once The Roof Assembly is installed, be sure to caulk anywhere that you can see daylight.

Pay extra attention to the gaps between the back edge of The Roof Assembly and the mounting surface.